Skip to content

8 services

Technical Support Unit for the Design and Test of Integrated Circuits

Characterization of prototype semiconductor devices and integrated circuits for mixed-signal, radio-frequency, optoelectronic and space applications; production testing of small series; electromagnetic compatibility studies, and design of test boards for high-performance mixed-signal prototypes.

Characterization of high-performance analog-digital circuits

Where it is done: A/D Measurement Lab

The Service offers a wide range of measurement capabilities, some of which are listed below:

  • Signal analysis in the frequency domain.
  • Signal analysis in the time domain.
  • Network analysis.
  • Electronic noise measurements.
  • Harmonic distortion measurements.
  • Impedance measurements of passive devices.
  • Acquisition and generation of logical patterns at high speed.
  • Analysis of standard communication protocols.
  • Digital signal integrity analysis.
  • Acquisition of signals of very low voltage level.
  • Jitter measurements.

A powerful range of equipment is available to carry out these measurements, including the Agilent 16902B and 16823A logic analyzers, 16720B pattern generators, HP3589A, SR770, HP4395A and HP3585A spectrum and network analyzers. Users can also have an important variety of oscilloscopes, among which it is worth highlighting the Agilent DSO81304B Infiniium with 40G samples/s and 13GHz of bandwidth and the LeCroy WaveJet 334A with 12 bits of vertical resolution.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
Characterization of high-performance AD circuits€793.89€869.50
Access to the high-performance AD circuits laboratory€474.03€519.18

Per day, in euros.

Ask about it

Characterization of RF circuits & devices

Where it is done: Radiofrequency Lab

The service offers the possibility of carrying out, among others, the following measures:

  • Spectrum analysis of RF signals.
  • Noise figure measurements.
  • Power measurements.
  • Characterization of low noise amplifier circuits (LNAs).
  • Impedance measurements.
  • Obtaining S parameters.
  • Analysis of communication protocols.
  • Generation and analysis of multi-tone signals.

To this end, it has the general-use radio frequency equipment that IMSE currently has, which includes, among others, the HP8719, Agilent E4440A, HP8562 and Agilent N5230 network/spectrum analyzers, HP8664 signal generators, Agilent 5182A vector signal generators and N8974A noise figure analyzer, which allow measurements up to a maximum of 13.5GHz.

The service also has an anechoic chamber for the characterization of emission/reception devices in a wide range of frequencies (700MHz-18GHz) as well as characterizing low-gain omnidirectional antennas. This equipment allows:

  • Obtaining radiation patterns.
  • Gain measure.
  • Directivity of antennas.
  • Isotropic sensitivity.

The equipment of this service is completed with a probe station with the capacity to carry out measurements up to 50GHz, both on wafers and on printed circuit boards.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
Characterization of RF circuits and devices€967.87€1,060.05
Access to the RF lab€648.02€709.73

Per day, in euros.

Ask about it

Electrical characterization of semiconductor devices

Where it is done: Device Characterization Lab

The service offers the necessary equipment and support to obtain the parameters that characterize the different semiconductor devices (CMOS transistors, BJT, diodes, LEDs, etc.). Among others, the service has the following measurement capabilities:

  • I/V measurements.
  • C/V measurements.
  • Pulsed I/V measurements.
  • Impedance measurements.
  • Accurate measurements of inductance, resistance and capacity.
  • Device reliability tests.

The facilities available include the HP4145, HP4155 and Agilent B1500 semiconductor characterization equipment, complemented by the ACS EOS 200TC and Thermonix T-2650V systems, which allow the temperature at which the devices can be tested to be modified. It also has CV HP4280A and LCR HP4285A measurement equipment, as well as a Karl Suss PSM6 probe station that allows characterization on wafers of up to 3.5 inches or unencapsulated devices.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
Access to the semiconductor characterization laboratory€684.01€749.16
Device characterization. Semiconductors€950.56€1,041.09

Per day, in euros.

Ask about it

Mixed functional characterization of circuits (ATE)

Where it is done: ATE Agilent 93000

The IMSE has an automatic Agilent 93000 mixed test system for the production test of devices and integrated circuits. The service offers the use of this equipment for testing small production series.

The system has the following configuration:

  • 80 fully individually configurable digital channels.
  • AWG-WGD (High Speed Arbitrary Signal Generator). Maximum output frequency (sinusoidal signal) of 125 MHz @ 500 MSPS and 12-bit resolution.
  • AWG-WGE (High Resolution Arbitrary Signal Generator). Maximum output frequency (sinusoidal signal) of 7.5 MHz @ 30 MSPS and 16-bit resolution.
  • WDA (High Speed Digitizer). 100MHz @ 41 MSPS bandwidth and 12-bit resolution.
  • 8 power supplies with maximum voltage/current of 8V / 8A per channel.

The service offer is complemented by the Thermonix T-2650V temperature forcing system that can be incorporated into the measurement setup for the characterization of circuits at different temperatures in the range between -20 and 200ºC.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
Test of electronic circuits with ATE€876.23€959.68

Per day, in euros.

Ask about it

Optoelectronic characterization of devices & circuits

Where it is done: Optoelectronics Lab

Users of the service can have a dark chamber with an optical bench and various equipment for the characterization of visible light sensors, as well as integrated circuits that include discrete sensors or matrices thereof. The laboratory is equipped with Oriel/Newport optical characterization equipment and class II and IIIa laser systems, as well as a PicoQuant pulsed laser system. The equipment is completed with objectives and all the opto-mechanical accessories necessary for testing this type of device and system.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
Access to the optoelectronic characterization laboratory€569.10€623.29
Characterization of Optoelectronic Devices and Circuits€835.64€915.23

Per day, in euros.

Ask about it

Printed circuit board (PCB) design

Where it is done: PCB Assembly Workshop

Over the years, IMSE has gained extensive experience in the design of printed circuit boards for the electrical characterization of mixed-signal integrated circuits, especially in high-speed, high-resolution analog-to-digital and digital-to-analog converters. This know-how has made it possible to make contributions to the state of the art in converter design and has positioned the Institute as a consolidated benchmark at a European level in this area of design.

This service offers the knowledge acquired in the design of printed circuit boards for the characterization of high-performance analog-digital circuits to other R&D groups of companies or research organizations.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
Printed circuit board design for testing€837.44€917.20

Per day, in euros.

Ask about it

Electromagnetic compatibility (EMC) studies

Where it is done: Radiofrequency Lab

The directives issued by the European Union on electromagnetic compatibility establish that commercialized devices must function satisfactorily in their electromagnetic environment without introducing intolerable disturbances to other equipment. To ensure this, they must undergo a certification process in an approved laboratory. This is an expensive process and, through the provision of the service, it is intended to offer, fundamentally to PYMEs (Small and medium business), a prior test environment that allows them to go to the approval laboratories in the best conditions to obtain certification.

This service is equipped with the anechoic chamber available to the IMSE and with the necessary equipment to undertake the tests.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
Electromagnetic compatibility (EMC) studies€934.30€1,023.28

Per day, in euros.

Ask about it

Single event test using pulsed laser technique

Where it is done: Pulsed Laser Lab

Electronic devices in space, defense, and medical applications are exposed to various types of radiation, including photons and high-energy particles (electrons, protons, neutrons and ions). Radiation can produce effects that may manifest as long-term parameter degradation (Total Ionization Dose or TID effects) or transient changes in the state of circuitry (Transient effects). While TID hardening of IC fabrication processes in general has improved in recent years, primarily due to reductions in gate oxide thicknesses and increases in doping densities, reduction in device dimensions have increased the sensitivity of devices to transient effects.

The service offers the possibility of studying the effect produced by the impact of a high-energy particle on a semiconductor device or circuit (Single-Event Effects or SEE) using the pulsed laser method, which is a powerful and low-cost tool for obtain information about the spatial and temporal dependence of the sensitivity of integrated circuits to radiation. The service equipment consists of a very compact femtosecond laser PULSBOX PICO-RAD 1064-50, manufactured by PULSCAN, which uses the single photon technique with a wavelength of 1064nm and a mixed signal oscilloscope MSO9404A for the output signal acquisition.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
Single event test with pulsed laser€941.81€1,031.51

Per day, in euros.

Ask about it

1 service

Technical Support Unit for Integrated Circuit Design Tools and Kits

It manages the CAD tools used at every stage of integrated circuit design, and the technology kits prototypes are made with:

  • Management of computer systems and communications equipment.
  • Support of design kits for the different foundries, versions of CAD tools and operating systems.
  • Management of MPCs and MPWs, and interface with CAD tool vendors and IC manufacturers.
  • Support for the management of training courses.

Support for the management of postgraduate and specialization courses

The Institute has an adequately equipped computer room for conducting postgraduate and specialization courses.

Apart from the courses organized by the center itself, the room can be used for training activities organized by other research centers, universities, companies and other public or private organizations.

Options and rates

Per day, in euros.
OptionPublic sectorExternal
General€84.09€92.10

Per day, in euros.

Ask about it